Category: O-Rings

Selecting Teflon® Encapsulated O-Rings for Reliable Sealing

Summary Introduction Teflon® encapsulated o-rings provide reliable sealing in environments where chemical exposure, temperature variation, or cleanliness requirements challenge standard elastomer materials. By combining a chemically resistant fluoropolymer jacket with a resilient elastomer core, these seals offer a practical solution when compatibility and long-term stability are critical to system performance. What Are Teflon® Encapsulated O-Rings? […]

How Tensile Strength Affects O-Ring Performance

Summary Introduction Tensile strength is a fundamental mechanical property that influences how elastomers respond to stress, deformation, and repeated loading. In sealing applications, this property helps determine whether an o-ring can withstand the mechanical demands encountered during installation and service. While tensile strength is often listed as a single value on a material datasheet, its […]

How O-Rings Ensure Reliable Connector Sealing

Summary The Role of O-Rings in Connector Sealing Systems In many applications, connectors serve as sealing interfaces that must protect the connection from external exposure while maintaining system integrity. O-Rings serve as the sealing element, helping connectors resist leakage and contaminant ingress. When integrated into the connector design, they create a barrier that helps protect […]

Viton® (FKM) O-Rings: Properties, Grades, and Industrial Applications

Summary What Are Viton® O-Rings? Viton® (FKM) o-rings are fluoropolymer elastomer seals engineered for extreme service conditions where standard rubber compounds fail. Developed in the late 1950s by DuPont, Viton® is a registered brand name for FKM — fluoroelastomer — a synthetic rubber defined by its high fluorine content. That fluorine content is the source […]

O-Ring Installation Best Practices

Summary Introduction O-Ring performance is often evaluated based on material selection, chemical compatibility, and operating conditions. However, installation is just as critical in determining whether a seal performs as intended. Some sealing issues attributed to material failure or poor design can result from improper handling, inadequate preparation, or incorrect installation techniques. Even a correctly specified […]

What are Bonded Seals

Summary What are Bonded Seals Bonded seals (Dowty Seals, Composite Washer Seals, Gasket Seals) are specialized sealing washers designed to prevent fluid or gas leaks around bolts, screws, and threaded fittings. Each seal consists of a flat metal washer with a rubber sealing element permanently bonded to its inner diameter. This dual-material construction combines the […]

O-Ring Materials, Applications, and Selection

Summary Introduction An o-ring is an elastomeric ring with a round cross-section that forms a seal by squeezing and applying pressure. That sealing mechanism depends on the elastomer returning toward its original shape after deformation (elastic recovery) and maintaining contact pressure against the gland surfaces over time. Because elastomers respond differently to heat, cold, fluids, […]

AFLAS® vs Viton® vs FFKM O-Ring Performance

Summary Introduction AFLAS® (FEPM/TFE-P), Viton® (FKM), and FFKM are often grouped together under the “fluoropolymer o-ring” label. Despite this shared classification, each material responds differently to environmental exposure. Real-world performance depends on how an elastomer ages under sustained operating conditions. Steam, alkaline media, solvents, and elevated temperatures introduce distinct degradation mechanisms that influence elasticity, hardness, […]

Thermal Aging vs Chemical Attack: Diagnosing Elastomer Seal Failures

Summary Thermal Aging vs. Chemical Attack in Elastomer Seals Elastomer seals fail for many reasons, but thermal aging and chemical attack are among the most common. Thermal aging degrades elastomers over time by altering the polymer’s internal structure and physical properties, while chemical attack damages seals through material incompatibility, leading to swelling, shrinkage, or loss […]

X-Ring’s Design, Performance, and Selection

Summary Introduction At a glance, an x-ring looks like a minor variation on a standard o-ring. Instead of a round cross-section, it features four distinct lobes. The subtle change in geometry, however, can meaningfully affect how a seal behaves. X-Rings, often called quad rings, are not intended to replace o-rings across the board. Rather, they […]